Electric cylinders · High-precision, high-load servo electric cylinder with customizable stroke EDA135
EDA135High-precision, high-load servo electric cylinder with customizable stroke EDA135 · EDA135
EDA135 belongs to High-precision, high-load servo electric cylinder with customizable stroke EDA135 in the Electric cylinders catalog.
EDA135 · Electric cylinders and linear actuators
An electric cylinder supplies a guided extension motion. Prepare the required thrust, stroke, speed, working cycle and load connection as one assembly requirement.
Comparing EDA135
For EDA135, read Accuracy Positioning | accuracy level, Ball diameter, Ball screw rigidity by the parameter group and variant shown. Compare screw and connection drawings for the proposed assembly. Check thrust, extension and speed together; separate upper limits do not establish a usable operating point.
Parameters and where they apply
| Accuracy Positioning | accuracy level Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Accuracy Positioning | accuracy level | C5/±0.01 |
|---|---|
| Accuracy Positioning | accuracy level Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Accuracy Positioning | accuracy level | C7/±0.02 |
| Ball diameter Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Ball diameter | 7.144mm mm |
| Ball diameter Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: SFS5020-3.8; Source column: Ball diameter | 6.35mm mm |
| Ball screw rigidity Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Ball screw rigidity | / |
| Ball screw rigidity Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: SFS5020-3.8; Source column: Ball screw rigidity | 66Kgf/μm Kgf/μm |
| C Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: C | 70 |
| C Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: C | 45 |
| C Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: C | — |
| C Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: C | — |
| C Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: C | — |
| Ca (KN) Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Ca (KN) | 104.1 KN |
| Ca (KN) Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: SFS5020-3.8; Source column: Ca (KN) | 13.7 KN |
| Center distance of synchronous wheel Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Center distance of synchronous wheel | 196mm mm |
| Coa (KN) Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Coa (KN) | 251.2 KN |
| Coa (KN) Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: SFS5020-3.8; Source column: Coa (KN) | 130.7 KN |
| Cor (KN) Current technical model · Bearing parameters:; Source row: Deep groove ball bearing 6211x2; Source column: Cor (KN) | 29.2 KN |
| Cor (KN) Current technical model · Bearing parameters:; Source row: Flat thrust bearing 51311; Source column: Cor (KN) | 246 KN |
| Cr (KN) Current technical model · Bearing parameters:; Source row: Deep groove ball bearing 6211x2; Source column: Cr (KN) | 43.4 KN |
| Cr (KN) Current technical model · Bearing parameters:; Source row: Flat thrust bearing 51311; Source column: Cr (KN) | 119 KN |
| D Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: D | 120 |
| D Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: D | 50 |
| D Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: D | 245 |
| D Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: D | 165 |
| D Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: D | 245 |
| Diameter Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Diameter | 50 mm mm |
| Driven gear specifications Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Driven gear specifications | 14M50T62 T |
| Driving gear specifications Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Driving gear specifications | 14M50T72 T |
| E Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: E | 10 |
| E Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: E | 10 |
| E Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: E | 10 |
| E Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: E | 10 |
| E Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: E | 10 |
| F Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: F | 14 |
| F Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: F | — |
| F Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: F | 40 |
| F Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: F | 60 |
| F Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: F | 40.3 |
| G Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: G | — |
| G Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: G | — |
| G Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: G | — |
| G Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: G | — |
| G Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: G | 85 |
| H Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: H | — |
| H Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: H | — |
| H Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: H | 85 |
| H Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: H | — |
| H Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: H | 86 |
| Lead of ball screw Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Lead of ball screw | 10mm mm |
| Lead of ball screw Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: SFS5020-3.8; Source column: Lead of ball screw | 20mm mm |
| Limit switch Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: Limit switch | Magnetic switch Proximity switch |
| M Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: M | M50x2 |
| M Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: M | M30x1.5 |
| M Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: M | — |
| M Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: M | — |
| M Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: M | — |
| Maximum allowed speed Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: Maximum allowed speed Rotation angle of piston rod | ≤250 mm/s mm/s |
| Maximum thrust allowed Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: Maximum thrust allowed | ≤100KN KN |
| Motor specifications that can be directly installed Current technical model · Optional configuration:; Source row: 10mm; Source column: Motor specifications that can be directly installed | 130框伺服 |
| Motor specifications that can be directly installed Current technical model · Optional configuration:; Source row: 10mm; Source column: Motor specifications that can be directly installed | 180框伺服 |
| Number of active gear teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Number of active gear teeth | 28 |
| Number of active gear teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 1.5:1; Source column: Number of active gear teeth | 24 |
| Number of active gear teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 2:1; Source column: Number of active gear teeth | 18 |
| Number of driven wheel teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Number of driven wheel teeth | 28 |
| Number of driven wheel teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 1.5:1; Source column: Number of driven wheel teeth | 36 |
| Number of driven wheel teeth Current technical model · Synchronous wheel and synchronous belt:; Source row: 2:1; Source column: Number of driven wheel teeth | 36 |
| Reducers that can be matched Current technical model · Optional configuration:; Source row: 10mm; Source column: Reducers that can be matched | 115A |
| Reducers that can be matched Current technical model · Optional configuration:; Source row: 10mm; Source column: Reducers that can be matched | 80A 100A 、 、130A、180A |
| Reducers that can be matched Current technical model · Optional configuration:; Source row: 20mm; Source column: Reducers that can be matched | 142A |
| Reducers that can be matched Current technical model · Optional configuration:; Source row: 20mm; Source column: Reducers that can be matched | 130A、180A |
| Rotation angle of piston rod Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: | ±0.3° ° |
| Scalable length Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: Scalable length | ≤2000mm mm |
| Screw shaft Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Screw shaft | 40K12 |
| Slenderness ratio Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Slenderness ratio | 1:50 |
| Synchronous belt circumference Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Synchronous belt circumference | 784 |
| Synchronous belt circumference Current technical model · Synchronous wheel and synchronous belt:; Source row: 1.5:1; Source column: Synchronous belt circumference | 812 |
| Synchronous belt circumference Current technical model · Synchronous wheel and synchronous belt:; Source row: 2:1; Source column: Synchronous belt circumference | 784 |
| Synchronous belt width Current technical model · Synchronous wheel and synchronous belt:; Source row: 1:1; Source column: Synchronous belt width | 50mm mm |
| Synchronous wheel speed ratio (input: output) Current technical model · Optional configuration:; Source row: 10mm; Source column: Synchronous wheel speed ratio (input: output) | 1:1 |
| Synchronous wheel speed ratio (input: output) Current technical model · Optional configuration:; Source row: 10mm; Source column: Synchronous wheel speed ratio (input: output) | 1.5:1 |
| Synchronous wheel speed ratio (input: output) Current technical model · Optional configuration:; Source row: 10mm; Source column: Synchronous wheel speed ratio (input: output) | 2:1 |
| Type Source condition; not yet structured · (Note: The parameters of the ball screw are applicable to strokes ≤ 300mm. For strokes greater than 300mm, please consult our technical personnel.) · Current technical model · Ball screw parameters; Source row: JFZ5010-8; Source column: Type | Ball screw |
| internal diameter Source condition; not yet structured · (Note: Thrust, stroke, and speed should be combined with actual usage, and the upper limit values of the three cannot be used together.) · Current technical model · Basic parameters:; Source row: 134x134 mm; Source column: internal diameter | φ120mm mm |
| ΦA Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: ΦA | Φ110 |
| ΦA Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: ΦA | Φ110 |
| ΦA Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: ΦA | Φ110 |
| ΦA Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: ΦA | Φ110 |
| ΦA Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: ΦA | Φ110 |
| ΦB Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: ΦB | Φ90 |
| ΦB Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: ΦB | Φ90 |
| ΦB Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: ΦB | Φ90 |
| ΦB Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: ΦB | Φ90 |
| ΦB Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: ΦB | Φ90 |
| ΦC Current technical model · Size Correspondence Table (Unit: mm); Source row: External thread; Source column: ΦC | — |
| ΦC Current technical model · Size Correspondence Table (Unit: mm); Source row: Internal thread; Source column: ΦC | — |
| ΦC Current technical model · Size Correspondence Table (Unit: mm); Source row: Type I connector; Source column: ΦC | Φ40 |
| ΦC Current technical model · Size Correspondence Table (Unit: mm); Source row: Fisheye bearing; Source column: ΦC | Φ50 |
| ΦC Current technical model · Size Correspondence Table (Unit: mm); Source row: Y-joint; Source column: ΦC | Φ40 |
Basic parameters
| Outer diameter | internal diameter | Maximum thrust allowed | Scalable length | Maximum allowed speed Rotation angle of piston rod | Limit switch | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 134x134 mm | φ120mm mm | ≤100KN KN | ≤2000mm mm | ≤250 mm/s | ±0.3° ° | Magnetic switch Proximity switch | |||||||||||||||||
Source-listed options
| Lead of ball screw | Synchronous wheel speed ratio (input: output) | Motor specifications that can be directly installed | Reducers that can be matched | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10mm mm | 1:1 | 1.5:1 | 2:1 | 130框伺服 | 180框伺服 | 115A | 80A 100A 、 、130A、180A | ||||||
| 20mm mm | 142A | 130A、180A | |||||||||||
Ball-screw parameters
| Ball screw model | Type | Diameter | Lead of ball screw | Ca (KN) | Coa (KN) | Ball screw rigidity | Ball diameter | Screw shaft | Slenderness ratio | Accuracy Positioning | accuracy level | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| JFZ5010-8 | Ball screw | 50 mm | 10mm mm | 104.1 KN | 251.2 KN | / | 7.144mm mm | 40K12 | 1:50 | C5/±0.01 | C7/±0.02 | |||||||||||
| SFS5020-3.8 | 20mm mm | 13.7 KN | 130.7 KN | 66Kgf/μm Kgf/μm | 6.35mm mm | |||||||||||||||||
Bearing parameters
| Bearing model | Cr (KN) | Cor (KN) | |||
|---|---|---|---|---|---|
| Deep groove ball bearing 6211x2 | 43.4 KN | 29.2 KN | |||
| Flat thrust bearing 51311 | 119 KN | 246 KN | |||
Timing pulleys and belt
| Synchronous wheel speed ratio | Driving gear specifications | Driven gear specifications | Number of active gear teeth | Number of driven wheel teeth | Center distance of synchronous wheel | Synchronous belt circumference | Synchronous belt width | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1:1 | 14M50T72 T | 14M50T62 T | 28 | 28 | 196mm mm | 784 | 50mm mm | |||||
| 1.5:1 | 24 | 36 | 812 | |||||||||
| 2:1 | 18 | 36 | 784 | |||||||||
Dimension correspondence table (mm)
| Load connection type | ΦA | ΦB | ΦC | C | D | E | F | H | G | M | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| External thread | Φ110 | Φ90 | — | 70 | 120 | 10 | 14 | — | — | M50x2 | ||||||||||||
| Internal thread | Φ110 | Φ90 | — | 45 | 50 | 10 | — | — | — | M30x1.5 | ||||||||||||
| Type I connector | Φ110 | Φ90 | Φ40 | — | 245 | 10 | 40 | 85 | — | — | ||||||||||||
| Fisheye bearing | Φ110 | Φ90 | Φ50 | — | 165 | 10 | 60 | — | — | — | ||||||||||||
| Y-joint | Φ110 | Φ90 | Φ40 | — | 245 | 10 | 40.3 | 86 | 85 | — | ||||||||||||
Talk to HTROBOT
- Emailemmy@htrobot.com
- Phone+86 152 0225 5004
- Alibaba storeVisit our Alibaba store